Original Shaping Disc 4-1/2" Diameter
Unlock the versatility of your ordinary angle grinder and let a Kutzall Shaping Wheel optimize your creative control! Shape, contour, hollow, trim, notch or make adjustments with ease as they wheel will be your go-to workhorse for any task.
The Shaping Discs allows you to effortlessly level high spots or adjust uneven surfaces. The structured teeth wrap over at the outer diameter, allowing for edge-on detailing. Despite their relatively flat shape, their slight curvature allows for controlled, free-hand, flat or convex shaping.
Product Dimensions
Mounting Guide
The Kutzall Shaping Wheels feature a 7/8” I.D and are intended to mount on a standard electric angle grinder with a 5/8” shaft. They mount on the 7/8” shoulder found on the flange or adapter included with most angle grinders. The flange is put on the grinder first, followed by the wheel and then the nut.
Caring for your Kutzall
Kutzall tools can be easily cleaned using a torch and/or a quick few passes with a soft wire brush, the heat will not harm the teeth!
Proposition 65
Compatible with most angle grinders
What Our Customers Are Saying
This wheel is the best wheel I have ever used. I do a lot of seat coping and where it was taking a couple hours per seat, I can now do it in 30 minutes. I filled that time saved for my family now.
Billy P.
I’m definitely impressed with the quality of these products. They are making my work much easier.
Sara K.
It just saves me massive amounts of time roughing out. I can get a carving ready to actually carve in half the time.
Don P.
Exactly what I was looking for. Got this to help remove material faster for sculpted chairs and it does not disappoint! I've used it on walnut, ash and mahogany and it eats it right up.
Ben G.
Soon as I started I was like WOW! This thing removes a lot of wood and smoothed it at the same time.
Manda S.
It does exactly what i expected from it. You have enough control to aggressively remove material or you can lightly shape a joint with this wheel. Leaves a good enough surface that some 100grit sandpaper cleans up nicely.
Joe J.
The Power Carver's Choice
Made in the U.S.A.
Free U.S. Shipping
- WWwarren w.Verified BuyerRated 5 out of 5 stars2 months agokutzall gets it done,
i have two of the shaping dish and one disc, i recently made a kayak seat out of red cedar, kutzall made it easy.
- MJMichael J.Verified BuyerRated 5 out of 5 stars6 months agoNew to carving
Being a newbie carver I was hoping Kutzall would be what I needed to try it out. It proved to be exactly what I needed. Using a variety of discs and bits I was very excited to see my first results. The discs are definitely confidence builders. I’m hooked.
- RSRandy S.Verified BuyerRated 5 out of 5 stars8 months agoGreat Product!
I purchased the 4 1/2 " original shaping disc to help with my first attempt at power carving a bowl. The disc performed like a dream! I was very happy with the quality and performance. I intend to purchase other Kutzall products in the near future.
- HMHarry M.Verified BuyerRated 5 out of 5 stars9 months agoGreat disk! But now what you need to make is ..
The fine abrasive disk has been my go-to for a long time. I have coarse and regular Kutzall disk as well as a number of Kutzall burrs, but this is my fave. My 'old' one is fine, but I bought another to mount on a fixed grinder so I could use them without conversion time. If you could make it in an even finer abrasive, I'd buy that as well. The only downside with the fine abrasive is that it tends to gum up if the wood isn't dry, but it cleans up fantastically with a quick soak in soapy water. I've never been in enough of a hurry to try to burn off gummy residue.
What would really be useful is a fine or medium burr in approximately the same profile as the cutting ball I use for most of my rough cutting. It would essentially be a burr that has an angle grinder attachment rather than a shaft. With this, I could finish and detail the interior of the spoons & bowls more easily and with greater control since I could hold onto the grinder with both hands. Holding onto the handle of a flex-shaft with both hands just isn't as stable. A low-quality product like this exists (https://tinyurl.com/224aa4uc), but it's not nearly as good as what I'd expect from Kutzall. And the abrasive is simply cut divots which would wear out quite quickly. The pix are examples of what I make using your products.
Thanks
Harry
- CMClifford M.Verified BuyerRated 5 out of 5 stars1 year agoGreat
This tool works great!
Use extreme caution this tool , it does a good job!